1. INTRODUCTION TO "SIF-CHAIRLIFTS"

      Module for fixed or detachable grip plants:
      Chairlifts, Gondola ropeways, Pulsé ropeways

 

Only one single Excel module coded in Visual-Basic makes it possible to solve all the problems relating to the designing and testing of the above cited plants. A user-friendly software interface is provided to facilitate working.

    • All the data can be loaded in numeric or graphic format through the mouse; the geometrical configurations of the line and land profile can be shown by means of a graph, either during data input or final result representation stages.
    • The numeric results are displayed to the User in Excel format, which makes it possible to change, integrate or export the test data.
    • All the results can be printed out: printing preview and the possibility to export the drawings in DXF format provide higher flexibility to the program
    • Sif-Monofuni is a program which uses a single Excel module inclusive of several Visual-Basic code modules

 

1.2 Responsibility

When using the programs, the user must be aware of the fact that no explicit or implicit guarantee is provided by the author of the SIF software and its distributors regarding the precision and reliability of the programs themselves.

The user must be familiar with the procedures used to make the calculations and must personally check all results supplied by the programs, assuming full responsibility for the correctness of the results obtained.

1.3 User licence

The purchase of the disks contained in this pack is instrumental in order to obtain the non-exclusive and non-transferable user licence for the program contained on these disks. This licence is granted to customers subject to the following

1.4 General conditions

The program, consisting of the information readable on the magnetic or optic medium and any other material attached to the disks, remains the property of the Author Ing. Vittoriano Vitali. The customer only purchases one user licence for the program which is valid for installation on a single machine.

The customer cannot alter or remove any brand, commercial name, serial number or other notices reserving rights inserted in the program and/or on its medium.

The user licence for the program does not include the faculty to obtain it a source format, or to have access to the relative project documentation, or the outline of any data files present in or created by the program.

In the event of a fault on the original disks, the author will replace the damaged disks with new disks after the damaged disks have been returned, charging the customer with the cost of shipping costs alone.

The need to check the suitability of the program as a means of obtaining particular results, its installation, and its use and management are the sole responsibility of the customer. The Author only guarantees that the magnetic or optical medium is free from manufacturing defects (if not, he undertakes to replace the disks free of charge after the damaged disks have been returned), excluding any other guarantee.

Under no circumstances will the Author of the software be responsible for damage of any kind connected and/or consequent to any defects in the quality, suitability, use and usability of the program.

The customer may not under any circumstances assigne or sub-license the licence to third parties.

Should the customer violate any of the obligations set out in the articles above, the Author may terminate the user licence in a simple written notice. In this event, the customer must abstain from making further use of the program and he may be asked to destroy any copies of the program that are in his possession in any form or to return them.

1.5 Program installation

To install SIF programs from CD-ROM, just insert the CD, which will automatically start the installation procedure. If not, use the command AVVIO (Start),  Run/Execution, d:\setup (where d: is the CD-ROM drive).

The procedure, after selecting the directory for program installation and copying all the required files, will ask you the licence user data.

WARNING: the data should be loaded in proper and complete mode so as to ensure proper future program performance.

 1.6 Program start up

To run the program at anytime as it is required, desktop link should be provided for direct connection to the MENU.XLS file into programs directory.

1.7 Instruction Manual and On-line Help

On-line Help is provided to make it possible for the user to get further information on the software or specific functions.

The Instruction Manual includes many files directly connected to the main file, called Index.

Each item in the Index is an active hypertext link which makes it possible for the User to "jump" to the selected text with a simple left-mouse click. The presence of an hypertext link is easily recognisable as the words are underlined and the mouse cursor changes its shape (from an arrow into a small hand).

1.8 On-line Service

On-line Service is provided through E-mail and Web pages at the Author's site
- The User can write e-mails to ask for more information or to report problems.
- Forms for program upgrade modules are available at the Author’s site.